Package swervelib.motors

Class TalonFXSwerve

java.lang.Object
swervelib.motors.SwerveMotor
swervelib.motors.TalonFXSwerve
All Implemented Interfaces:
AutoCloseable
public class TalonFXSwerve extends SwerveMotor
TalonFX Swerve Motor. Made by Team 1466 WebbRobotics.

  • Field Details

    • STATUS_TIMEOUT_SECONDS

      public static double STATUS_TIMEOUT_SECONDS
      Wait time for status frames to show up.

  • Constructor Details

    • TalonFXSwerve

      public TalonFXSwerve(TalonFX motor, boolean isDriveMotor, DCMotor motorType)
      Constructor for TalonFX swerve motor.
      Parameters:
      motor - Motor to use.
      isDriveMotor - Whether this motor is a drive motor.
      motorType - DCMotor which the TalonFX is attached to.

    • TalonFXSwerve

      public TalonFXSwerve(int id, String canbus, boolean isDriveMotor, DCMotor motorType)
      Construct the TalonFX swerve motor given the ID and CANBus.
      Parameters:
      id - ID of the TalonFX on the CANBus.
      canbus - CANBus on which the TalonFX is on.
      isDriveMotor - Whether the motor is a drive or steering motor.
      motorType - DCMotor which the TalonFX is attached to.

    • TalonFXSwerve

      public TalonFXSwerve(int id, boolean isDriveMotor, DCMotor motorType)
      Construct the TalonFX swerve motor given the ID.
      Parameters:
      id - ID of the TalonFX on the canbus.
      isDriveMotor - Whether the motor is a drive or steering motor.
      motorType - DCMotor which the TalonFX is attached to.

  • Method Details

    • factoryDefaults

      public void factoryDefaults()
      Configure the factory defaults.
      Specified by:
      factoryDefaults in class SwerveMotor

    • close

      public void close()
      Specified by:
      close in interface AutoCloseable
      Specified by:
      close in class SwerveMotor

    • clearStickyFaults

      public void clearStickyFaults()
      Clear the sticky faults on the motor controller.
      Specified by:
      clearStickyFaults in class SwerveMotor

    • setAbsoluteEncoder

      public SwerveMotor setAbsoluteEncoder(SwerveAbsoluteEncoder encoder)
      Set the absolute encoder to be a compatible absolute encoder.
      Specified by:
      setAbsoluteEncoder in class SwerveMotor
      Parameters:
      encoder - The encoder to use.
      Returns:
      The SwerveMotor for single line configuration.

    • configureIntegratedEncoder

      public void configureIntegratedEncoder(double positionConversionFactor)
      Configure the integrated encoder for the swerve module. Sets the conversion factors for position and velocity.
      Specified by:
      configureIntegratedEncoder in class SwerveMotor
      Parameters:
      positionConversionFactor - The conversion factor to apply for position.


      Degrees:
      360 / (angleGearRatio * encoderTicksPerRotation)


      Meters:
      (Math.PI * wheelDiameter) / (driveGearRatio * encoderTicksPerRotation)

    • configurePIDF

      public void configurePIDF(PIDFConfig config)
      Configure the PIDF values for the closed loop controller. 0 is disabled or off.
      Specified by:
      configurePIDF in class SwerveMotor
      Parameters:
      config - Configuration class holding the PIDF values.

    • configurePIDWrapping

      public void configurePIDWrapping(double minInput, double maxInput)
      Configure the PID wrapping for the position closed loop controller.
      Specified by:
      configurePIDWrapping in class SwerveMotor
      Parameters:
      minInput - Minimum PID input.
      maxInput - Maximum PID input.

    • disablePIDWrapping

      public void disablePIDWrapping()
      Disable PID Wrapping on the motor.
      Specified by:
      disablePIDWrapping in class SwerveMotor

    • setMotorBrake

      public void setMotorBrake(boolean isBrakeMode)
      Set the idle mode.
      Specified by:
      setMotorBrake in class SwerveMotor
      Parameters:
      isBrakeMode - Set the brake mode.

    • setInverted

      public void setInverted(boolean inverted)
      Set the motor to be inverted.
      Specified by:
      setInverted in class SwerveMotor
      Parameters:
      inverted - State of inversion.

    • burnFlash

      public void burnFlash()
      Save the configurations from flash to EEPROM.
      Specified by:
      burnFlash in class SwerveMotor

    • set

      public void set(double percentOutput)
      Set the percentage output.
      Specified by:
      set in class SwerveMotor
      Parameters:
      percentOutput - percent out for the motor controller.

    • setReference

      public void setReference(double setpoint, double feedforward)
      Set the closed loop PID controller reference point.
      Specified by:
      setReference in class SwerveMotor
      Parameters:
      setpoint - Setpoint in MPS or Angle in degrees.
      feedforward - Feedforward in volt-meter-per-second or kV.

    • setReference

      public void setReference(double setpoint, double feedforward, double position)
      Set the closed loop PID controller reference point.
      Specified by:
      setReference in class SwerveMotor
      Parameters:
      setpoint - Setpoint in meters per second or angle in degrees.
      feedforward - Feedforward in volt-meter-per-second or kV.
      position - Only used on the angle motor, the position of the motor in degrees.

    • getVoltage

      public double getVoltage()
      Get the voltage output of the motor controller.
      Specified by:
      getVoltage in class SwerveMotor
      Returns:
      Voltage output.

    • setVoltage

      public void setVoltage(double voltage)
      Set the voltage of the motor.
      Specified by:
      setVoltage in class SwerveMotor
      Parameters:
      voltage - Voltage to set.

    • getAppliedOutput

      public double getAppliedOutput()
      Get the applied dutycycle output.
      Specified by:
      getAppliedOutput in class SwerveMotor
      Returns:
      Applied dutycycle output to the motor.

    • getVelocity

      public double getVelocity()
      Get the velocity of the integrated encoder.
      Specified by:
      getVelocity in class SwerveMotor
      Returns:
      velocity in Meters Per Second, or Degrees per Second.

    • getPosition

      public double getPosition()
      Get the position of the integrated encoder.
      Specified by:
      getPosition in class SwerveMotor
      Returns:
      Position in Meters or Degrees.

    • setPosition

      public void setPosition(double position)
      Set the integrated encoder position.
      Specified by:
      setPosition in class SwerveMotor
      Parameters:
      position - Integrated encoder position. Should be angle in degrees or meters.

    • setVoltageCompensation

      public void setVoltageCompensation(double nominalVoltage)
      Set the voltage compensation for the swerve module motor.
      Specified by:
      setVoltageCompensation in class SwerveMotor
      Parameters:
      nominalVoltage - Nominal voltage for operation to output to.

    • setCurrentLimit

      public void setCurrentLimit(int currentLimit)
      Set the current limit for the swerve drive motor, remember this may cause jumping if used in conjunction with voltage compensation. This is useful to protect the motor from current spikes.
      Specified by:
      setCurrentLimit in class SwerveMotor
      Parameters:
      currentLimit - Current limit in AMPS at free speed.

    • setLoopRampRate

      public void setLoopRampRate(double rampRate)
      Set the maximum rate the open/closed loop output can change by.
      Specified by:
      setLoopRampRate in class SwerveMotor
      Parameters:
      rampRate - Time in seconds to go from 0 to full throttle.

    • getMotor

      public Object getMotor()
      Get the motor object from the module.
      Specified by:
      getMotor in class SwerveMotor
      Returns:
      Motor object.

    • getSimMotor

      public DCMotor getSimMotor()
      Get the DCMotor of the motor class.
      Specified by:
      getSimMotor in class SwerveMotor
      Returns:
      DCMotor of this type.

    • usingExternalFeedbackSensor

      public boolean usingExternalFeedbackSensor()
      Queries whether the absolute encoder is directly attached to the motor controller.
      Specified by:
      usingExternalFeedbackSensor in class SwerveMotor
      Returns:
      connected absolute encoder state.